Your Complete Instruction for Installing a Bathtub
Your Complete Instruction for Installing a Bathtub
Blog Article
Are you currently trying to locate info around Installing A Bathtub?
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough task. If the old bathtub is easily obtainable, the task can relocate easily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the task and fit attempting it. Instead of hiring a service provider to take control of a halfway-completed job, it is better to consider utilizing one before you start. Chances are you may require an expert plumber to make tube connections.
This post will help you install a brand-new tub in your restroom if you have already gotten a brand-new tub as well as don't need to change the setup of your previous water system pipelines.
Your devices as well as material checklist must comprise the following:
Getting ready for the Setup
Firstly, the supporting frame provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly originate from the pipes. When the supply pipes have been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before moving on to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bath tub in the needed position. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub till the level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the tub and also examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bathtub must wait until the bath tub has been used at least once as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin ensuring that the washers remain in area between the tap and the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former type needs to be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can split fairly very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly readily available on the market. It is advisable to fit the tiles using waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very drawn to A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the new post. Enjoyed reading our article? Please share it. Let other people locate it. Many thanks for going through it.
Pro help, one ring away. Report this page